Compared with other similar pumps, Model-S horizontal medium-open pump is featured with long life, high efficiency, reasonable structure. low operating cost, convenient installation and repair, etc. It is an ideal pump for fire fighting.air-conditioning. chemical. water treatment and other industries.
The designed pressures of the pump are 1.6 Mpa and 2.0 Mpa, In order to meet different users' requirements around the world, the relevant inlet and outlet flanges of pump body can be chosen according to ANSI, PN and JIS standards. These inlet and outlet flanges are all installed in the lower part of pump body,so the rotor can be taken out without disassembling pipelines of the system,and it is convenient to repair.Part of the pump body adopts a double-fow-passage structure in design, which Can lower the radial force and extend the lie of the mechanic seal and the bearing.
The hydraulic design of the blade wheel uses the up- to-date CFD technology,which can improve the hydraulic efficiency of the pump. The blade wheel has been made in a dynamic balance,so as to make sure that model -S pump can wok very smoothly.
The diameter of the shaft is big. while the gap between bearings is short. This can lower the deflection of the shaft, so as to extend the life of the mechanic seal and the bearing.
For model-S pumps.the shaft casting can be made of many different materials,so as to protect the shaft from corrosion and abrasion. The shaft casing can be replaced.
A replaceable abrasion ring is installed between the pump body and blade wheel, so as to protect the pump body and blade wheal from abrasion. lt is convenient to replace.This results in low maintenance cost, guarantees enough running gap and high efficiency.
The pump with unique stuffing design can use not only stuffing. but also mechanic seal .The seal device can be replaced without disassembling pump cover.
The unique bearing design makes it possible that the bearing can use either grease or thin oil for lubrication. The designed lie of the bearing can be up to more than 100,000 hours. A double-row Thrust Bearing or closod -typo bearing can also be used.
According to actual demands of users. the materials of model-S horizontal medium-open pump can be copper, cast iron, nodular cast iron, 316 stainless steel,416 stainless steel, duplex steel. Hastelloy, monel metal, Titanium alloy,20# alloy,etc.
Model-S pump can be installed in two ways: horizontal and vertical installments.The vertical installment can save floor space.
As an important form of centrifugal pump, double suction pump is widely used in engineering because of its high lift and large flow. The impeller of this pump type is actually a combination of two back-to-back impellers, and the water flow from the impellers merges into a volute. The double-suction pump has the following characteristics: it is equivalent to two single-suction impellers of the same diameter working at the same time, and the flow rate can be doubled under the same outer diameter of the impeller; the pump casing is horizontally opened, which is convenient for inspection and maintenance. The inlet and outlet of the suction pump are in the same direction and perpendicular to the pump shaft, which is conducive to the arrangement and installation of the pump and the inlet and outlet pipes; the impeller structure of the double suction pump is symmetrical, there is no axial force, and the operation is relatively stable.
China Double Suction Pump,Double Suction Centrifugal Pump manufacturers, welcome Double Suction Water Pump,Carbamide Pump purchasers from worldwide to visit our site.
Jiangsu Qiantu Trading Co., Ltd.
- Company Name: Jiangsu Qiantu Trading Co., Ltd.
- Representative: RAY
- Product/Service: Magnetic pump , Self priming pump , centrifugal pump , Fluoroplastic pump , Stainless steel insulation pump , Butterfly valve
- Capital (Million US $): 10000000RMB
- Year Established: 2007
- Total Annual Sales Volume (Million US $): US$50 Million - US$100 Million
- Export Percentage: 41% - 50%
- Total Annual Purchase Volume (Million US $): US$50 Million - US$100 Million
- No. of Production Lines: 8
- No. of R&D Staff: 11 -20 People
- No. of QC Staff: 11 -20 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): 10,000-30,000 square meters
- Factory Location: Nanning Road,Jingjiang District,Taizhou City,Jiangsu Province,China
- Contact Person: Mr. Ray
- Tel: 86-523-82624186
Premium Related Products